IP7180 Custom Electric Lifting Column | OEM Configuration

IP7180 custom electric lifting column for OEM equipment

IP7180 is a configurable electric lifting-column platform for OEM equipment and vertical-motion systems. Final suitability depends on the selected electrical and mechanical configuration, required load, travel, movement speed, mounting geometry, controller, synchronization requirements, duty cycle and operating environment.

For platform comparison, review ActuLift colonnes de levage électriques, colonnes élévatrices télescopiques et industrial and mobile column lifts before locking the architecture.

Configuration data to confirm before quotation

• Required supply voltage and controller architecture.
• Required axial, dynamic and holding load in the real mechanism.
• Required travel, retracted height and extended height.
• Required movement speed under the expected load.
• Column orientation, mounting geometry and frame support.
• Expected operating frequency and duty cycle.
• Feedback, synchronization, limit and safety-function requirements.
• Controller, handset, cable, connector and wiring requirements.
• Required environmental or ingress-protection level.
• Required drawings, test records and compliance documentation.

Load and mechanical integration

Lifting-column capacity should be confirmed from the complete load case rather than inferred from a generic catalog figure. Provide the axial load, moving load, holding load, load center, mounting direction, frame support, off-center forces and safety factor before selecting the final IP7180 configuration.

The surrounding frame should guide the motion and reduce unnecessary side loading or misalignment. Confirm column spacing, mounting holes, brackets and structural support during drawing review. Related hardware can be reviewed under Solutions OEM/ODM sur mesure.

Travel and movement-speed selection

Required travel should be derived from the finished equipment geometry. Confirm retracted height, extended height, available installation space and required vertical movement on an approved drawing rather than assuming one universal travel range.

Movement speed should be validated under the real working load with the selected controller and drive configuration. Sample testing should check lift time, current draw, vibration, end-of-travel behavior and mechanical interference.

Electrical, control and synchronization planning

Confirm the applicable supply specification, rated and peak current, controller capacity, cable length, connector type and wiring scheme for the selected IP7180 build.

If the system uses multiple columns or requires position feedback, limit confirmation or synchronized movement, confirm the exact sensor, controller and synchronization method before approval. Related options can be reviewed under control boxes and controllers et les télécommandes et appareils manuels.

Environmental and protection requirements

Environmental suitability depends on the exact column build, seals, cable exits, connectors, mounting orientation and surrounding equipment. If the project requires a specific ingress-protection level, cleaning method, temperature range, humidity limit or exposure condition, request the current supporting test basis or documentation for the ordered configuration.

Projects driven by moisture exposure can also review ActuLift actionneurs linéaires étanches, but the final IP7180 protection requirement still needs product-specific evidence.

Noise, duty-cycle and lifecycle validation

For equipment used near people, define an acceptable sound target and test the complete system under load. Frame resonance, brackets, panels, guides, controller behavior and installation quality can materially change the sound of the finished equipment.

Duty cycle and service-life requirements should be matched to the actual ON/OFF pattern, load and ambient conditions. Request applicable validation data if the project has a defined continuous-operation, lifecycle or safety requirement.

Application and system fit

IP7180 can be evaluated for workstations, benches, furniture, industrial fixtures and other vertical-motion equipment, but application fit should be confirmed from the complete mechanical, electrical and control design rather than from a generic industry label.

If the finished system is a desk or workstation, compare the column plan with ActuLift cadres de bureaux debout et jambes de base before finalizing the structure.

Compliance and documentation

For export programs, regulated equipment or customer quality systems, request the documentation package for the exact IP7180 configuration. Depending on the project, this may include dimensional drawings, electrical specifications, wiring information, inspection records, material information, environmental test evidence or available compliance declarations.

Do not treat generic page wording as proof that CE, RoHS or another certification applies unchanged to every configuration or to the buyer’s finished machine.

OEM buyer checklist

• Confirm the exact IP7180 configuration before sample approval.
• Confirm load case, travel, speed and mounting geometry from the real mechanism.
• Confirm supply, current, wiring, controller and handset compatibility.
• Confirm feedback or synchronization requirements where applicable.
• Confirm environmental/protection requirements with supporting documentation.
• Confirm duty-cycle and lifecycle requirements from the actual use case.
• Confirm the documentation package required before bulk approval.

Where IP7180 fits

IP7180 is best treated as a configurable custom electric lifting-column platform for OEM vertical-motion systems rather than a fixed universal specification. Use the product page to begin sourcing, then lock the electrical, mechanical, control, environmental and documentation requirements through drawings, samples and project-specific validation.