IP600 Electric Linear Actuator | OEM Configuration

IP600 electric linear actuator for OEM equipment

IP600 is a configurable electric linear actuator platform for OEM equipment. The product is currently cataloged in ActuLift’s 24V actuator range, while final electrical suitability depends on the selected build, controller and power system.

For sourcing and family comparison, review ActuLift actionneurs linéaires 24V, actionneurs linéaires lourds and the broader actionneur linéaire range before locking the design.

Configuration data to confirm before quotation

• Required supply voltage and electrical limits.
• Required push and pull load in the real mechanism.
• Required stroke, retracted length and extended length.
• Required movement speed under the expected load.
• Mounting geometry, linkage angle and side-load control.
• Expected operating frequency and duty cycle.
• Feedback, limit or position-signal requirements.
• Controller, cable, connector and wiring requirements.
• Required environmental or ingress-protection level.
• Required drawings, test records and compliance documentation.

Load and mechanical integration

Actuator capacity should be confirmed from the complete mechanism rather than inferred from a generic page value. Provide the push/pull load, installation angle, leverage, friction, side-load risk and any peak loads before selecting the final IP600 configuration.

Mounting details can materially change the effective actuator load and service behavior. Confirm pin locations, bracket spacing and available installation distance during drawing review. Related hardware can be reviewed under Solutions OEM/ODM sur mesure.

Stroke and movement-speed selection

Required stroke and movement speed should be specified for the exact application and validated under the real working load. Different gearing, loads and travel requirements can change movement time, current draw and practical performance.

Before quotation, provide the required stroke, installation dimensions and motion-time target. Sample validation should check full travel, end-of-stroke behavior, current draw, vibration and mechanical interference.

Electrical, feedback and control matching

The current catalog places IP600 in ActuLift’s 24V range, but the complete electrical design still needs configuration-specific confirmation. Confirm supply limits, rated and peak current, switching method, cable length, connector capacity and controller interface for the selected build.

If the project requires feedback, synchronization, limit confirmation or host-system control, confirm the exact sensor and signal arrangement before approval rather than assuming a specific feedback method from the model family. Related options can be reviewed under actionneurs avec retour d'information / contrôleur et control boxes and controllers.

Environmental and protection requirements

Environmental suitability depends on the exact actuator build, seals, cable exits, connectors, mounting direction and surrounding equipment. If the project requires a specific ingress-protection level, cleaning method, temperature range, humidity limit or outdoor exposure condition, request the current supporting test basis or documentation for the ordered configuration.

Projects driven by environmental exposure can also review ActuLift actionneurs linéaires étanches, but the final protection requirement still needs product-specific evidence.

Noise, duty-cycle and lifecycle validation

For equipment used near people, define an acceptable sound target and test the actuator inside the finished mechanism. Brackets, panels, guides, load direction and controller behavior can materially change system noise.

Duty cycle and service-life requirements should be matched to the actual ON/OFF pattern, load and ambient conditions. Request applicable validation data if the project has a defined continuous-operation, overload-protection, power-loss holding or lifecycle requirement.

Compliance and documentation

For export programs, regulated equipment or customer quality systems, request the documentation package for the exact IP600 configuration. Depending on the project, this may include drawings, product specifications, wiring information, inspection records, material information, environmental test evidence or available compliance declarations.

Do not treat generic page wording as proof that a certification, protection level or performance value applies unchanged to every configuration or to the buyer’s finished machine.

OEM buyer checklist

• Confirm the exact IP600 configuration before sample approval.
• Confirm load, stroke, speed and mounting geometry from the real mechanism.
• Confirm supply, current, wiring, connectors and controller compatibility.
• Confirm feedback, limit or synchronization requirements where applicable.
• Confirm environmental/protection requirements with supporting documentation.
• Confirm duty-cycle, lifecycle and power-loss behavior requirements from the actual use case.
• Confirm the documentation package required before bulk approval.

Where IP600 fits

IP600 is best treated as a configurable electric linear actuator platform for OEM motion systems rather than a fixed universal specification. Use the product page to begin sourcing, then lock the exact electrical, mechanical, environmental and documentation requirements through drawings, samples and project-specific validation.